<span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">手电两用螺杆启闭机装置<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(1) 手电两用螺杆式启闭机装置 ：应按制造厂提供的图纸和技术阐明书要求停止安 装、 调试和试运转。 装置好的启闭机, 其机械和电气设备等的各项功能应契合施 工图约及制造厂技术阐明书的要求;<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(2) 装置启闭机的根底修建物, 必需稳定平安, 机座和根底构件的砼应按施 工图纸的规则浇注, 在砼强度尚未到达设计强度时, 不准撤除和改动启闭机的临 时支撑;<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(3) 启闭机设备的装置应按 DL/T5019-94有关规则停止;<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(4) 电气设备的装置均按施工图纸、 制造厂技术阐明书的规则执行, 全部电 气设备应牢靠接地;<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(5) 启闭机装置终了后均对启闭机停止清算, 修补已损坏的维护油漆, 并灌 注光滑脂;<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(6) 启闭机装置完成后, 要停止空载实验、 带荷载实验, 实验均应契合施工 图纸和 DL/T5019-94的相关规则。<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(7) 装置先手电两用启闭机座的纵横向中心线与闸门吊耳实践地位的起吊 中心线的间隔偏向控制在±2mm 之内,高程偏向不超越±5mm 。<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(8) 机座与根底板严密接触,其间隙在任何部位都不超越 0.5mm 。<br style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;" /><span style="font-family: "Microsoft YaHei", 微软雅黑, STHeiti, "WenQuanYi Micro Hei", SimSun, sans-serif; font-size: 16px; text-align: justify; text-indent: 32px;">(9) 螺杆装置,其外径母线直线度公差小于 1000:0.6,且全长不超越杆长 的 4000:1。